Router Bits & Woodworking Products

Average Customer Rating: (3 reviews)
Add your own review for this product

By Bruce Patrick (Wetumpka AL US)

I have been making cabinets for over 25 years and have been using MLCS bits for most of that time. I fins that the bits are always good quality and their prices will beat anyone else. I highly recommend them to anyone who is looking for good bits at a great price.

By Anthony Boedeker (Independence Ke US)

I have been a customer of MLCS since the early 80's and I am still using some of the bits I bought back then. I have 3 different sets of the rail and stile bits and they have never let me down. I have recommended MLCS to all of my woodworking friends and will continue to use them. They are the best bit for the cost.

By Walt Jones (West Chester Pa )

I have owned a stacked rail & Stile stacked bit for about a year, but only used it recently. After a few test pices I saved the perfect pices for setups.

I have now used the bit w/a router lift to mill maple, cherry and beach - what a pleasure. No bit changing - quick set up clean profiles. I built shop made sled that accmodates a backup to avoid tearout. As long as you mill your stock properly your doors will be perfect.

Add your own review for this product

Average Customer Rating: (3 reviews)
Add your own review for this product

By johnnie raymond moreno II (brady TX US)

I'm a shop carpenter. so i made my own sled..at a fraction of the price ..around $15... plus i work in a full furniture shop...any ways for the good stuff ...i found out that if you start on the inside cut first and then the end cuts it goes much much faster. and when you do that you can use your inside cuts to aline the side cuts faster, and with out the set up blocks. makes some great cuts..will order others from this line of bits ...Also remember to add 3/4" to the total length of your pieces that you want to go on the inside ..this can be the rail or stile ....

By Bruce Patrick (Wetumpka AL US)

I have been using MLCS router bits for many years and recently purchased my first stacked bit for making raised panel doors. This is a great idea and I wish that they had all their profiles in this product. I love them, no stopping to restack the bit or change the bit. Just change the height and continue cutting. A great time saver.

By Bill Holstein (Newport WA US)

In spite of what is shown in the video, when you make the first cut with the top part of the bit, the lower cutter is high enough to cut into the base of the sled. This removes the edge that rides against the fence and next time you go to cut another end cut, the edge of the sled is cut away and the sled rocks against the fence. Basically it ruined the sled. to overcome this I cut a piece of 1/4" masonite to fit on top of the sled base and put a slot to match the one in the base that the handle slides in to thighten the block against the stock. Since the sled edge was already cut away, this scarificial piece has the edge cut away by the lower cutter of the bit and I can throw it away when I am done making the end cuts. You still have to make sure the sled does not rock as you slide it along the fence because the edge is still being cut away by the lower cutter.

Add your own review for this product

No rating yet... Be the first to rate this product!

Average Customer Rating: (2 reviews)
Add your own review for this product

By Ruben andrade ( Vi US)

No comment.

By Kim Morgenthaler (Saratoga CA US)

I ordered this along with the stacked Shaker Rail and Stile Bit. I wondered, with this thinner slot cutter, if the rail "tongue" would then be too wide to fit into the slot. These clever engineers recessed the mating surfaces of the slot cutter to accept the bearing and lower cutter. Using the amply supplied shims, I achieved a fantastic joint. The 5mm panels (more and more common) fit the 5.2mm groove perfectly! I couldn't be more thrilled with this product and highly recommend it!

Add your own review for this product